Feature Codes for the FlashTalk Model 4 with Flash ACD

Andrew · July 17th, 2003, 10:46 AM

Depending on how your system was programmed the following feature codes are broken out into two ranges.

High Range (this is the standard factory range)

Leave Message - "Feature" 9 8 0 (Used by VM only)
Open Mailbox - "Feature" 9 8 1 (Used by VM & ACD)
Operator/Service Control - "Feature" 9 8 2 (Used by VM & ACD)
System Administration - "Feature" 9 8 3 (Used by VM & ACD)
Log in/out - "Feature" 9 8 4 (Used by ACD only)
Flash DN - "Feature 9 8 5 (Used by VM & ACD)
Transfer - "Feature" 9 8 6 (Used by VM only)
Interrupt - "Feature 9 8 7 (Used by VM only)
Busy Mode - "Feature" 9 8 8 (Used by ACD only)
Queue - "Feature" 9 8 9 (Used by ACD only)
List Feature - "Feature" 9 * 1 (Used by VM & ACD)

Low Range

Leave Message - "Feature" 9 1 0 (Used by VM only)
Open Mailbox - "Feature" 9 1 1 (Used by VM & ACD)
Operator/Service Control - "Feature" 9 1 2 (Used by VM & ACD)
System Administration - "Feature" 9 1 3 (Used by VM & ACD)
Log in/out - "Feature" 9 0 4 (Used by ACD only)
Flash DN - "Feature 9 0 5 (Used by VM & ACD)
Transfer - "Feature" 9 0 6 (Used by VM only)
Interrupt - "Feature 9 0 7 (Used by VM only)
Busy Mode - "Feature" 9 0 8 (Used by ACD only)
Queue - "Feature" 9 0 9 (Used by ACD only)
List Feature - "Feature" 9 * 5 (Used by VM & ACD)

**After you have chosen a Feature Code range, the Feature Code (F903) is disabled. To change your Feature Code range you must reinstall the FlashTalk.

July 17th, 2003, 10:46 AM	#1 (permalink)
Andrew Moderator Join Date: Jul 2003 Posts: 159	Feature Codes for the FlashTalk Model 4 with Flash ACD Depending on how your system was programmed the following feature codes are broken out into two ranges. High Range (this is the standard factory range) Leave Message - "Feature" 9 8 0 (Used by VM only) Open Mailbox - "Feature" 9 8 1 (Used by VM & ACD) Operator/Service Control - "Feature" 9 8 2 (Used by VM & ACD) System Administration - "Feature" 9 8 3 (Used by VM & ACD) Log in/out - "Feature" 9 8 4 (Used by ACD only) Flash DN - "Feature 9 8 5 (Used by VM & ACD) Transfer - "Feature" 9 8 6 (Used by VM only) Interrupt - "Feature 9 8 7 (Used by VM only) Busy Mode - "Feature" 9 8 8 (Used by ACD only) Queue - "Feature" 9 8 9 (Used by ACD only) List Feature - "Feature" 9 * 1 (Used by VM & ACD) Low Range Leave Message - "Feature" 9 1 0 (Used by VM only) Open Mailbox - "Feature" 9 1 1 (Used by VM & ACD) Operator/Service Control - "Feature" 9 1 2 (Used by VM & ACD) System Administration - "Feature" 9 1 3 (Used by VM & ACD) Log in/out - "Feature" 9 0 4 (Used by ACD only) Flash DN - "Feature 9 0 5 (Used by VM & ACD) Transfer - "Feature" 9 0 6 (Used by VM only) Interrupt - "Feature 9 0 7 (Used by VM only) Busy Mode - "Feature" 9 0 8 (Used by ACD only) Queue - "Feature" 9 0 9 (Used by ACD only) List Feature - "Feature" 9 * 5 (Used by VM & ACD) **After you have chosen a Feature Code range, the Feature Code (F903) is disabled. To change your Feature Code range you must reinstall the FlashTalk.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Flash Acd	hnm1	Norstar systems	3	August 15th, 2005 03:03 PM
Nortel Option 61C Feature Access Codes	staffnet	Meridian systems	1	November 20th, 2004 09:56 PM
Charge Account Feature Codes in MAT6 showing on non-ACD sets	redG	Meridian systems	0	December 6th, 2003 01:34 PM
Default Feature Codes for FlashTalk	Andrew	Norstar systems	0	July 10th, 2003 10:39 AM
To find out what Feature Codes FlashTalk is using	Andrew	Norstar systems	0	July 10th, 2003 10:23 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)