How do I test members in a trunk group

redG · December 11th, 2003, 10:15 AM

We have a G3r switch. We have a TAC of 801, the type is tie, and it has 207 members. We are going to cut over our 11 T1's to a fiber backbone and I need to be able to test the circuits after the cut. Can someone tell me how I can test a specific member in a trunk group?

Any help is appreciated.

mrgold · December 11th, 2003, 11:24 AM

Quote:

Originally Posted by redG

We have a G3r switch. We have a TAC of 801, the type is tie, and it has 207 members. We are going to cut over our 11 T1's to a fiber backbone and I need to be able to test the circuits after the cut. Can someone tell me how I can test a specific member in a trunk group?

Any help is appreciated.

Use your trunk access code followed by the port.
Example:
797{tac} 01 4(a=1, b=2, c=3, etc.) 01 01
then just dial a number

nexSIP · December 11th, 2003, 09:12 PM

Quote:

Originally Posted by mrgold

Use your trunk access code followed by the port.
Example:
797{tac} 01 4(a=1, b=2, c=3, etc.) 01 01
then just dial a number

This doesnt work on ISDN PRI circuits. I just make a call then busy out that board then move to the next one. Also if you are using NFAS trunk make sure your D-channels switch back and forth for fun.

bharris · December 23rd, 2003, 07:18 PM

Use the following command.

status trunk 1/1

This gives the status for trunk number 1 member number 1. Use the trunk number(s) you have.

seawolf · April 4th, 2005, 10:12 AM

Quote:

Originally Posted by redG

We have a G3r switch. We have a TAC of 801, the type is tie, and it has 207 members. We are going to cut over our 11 T1's to a fiber backbone and I need to be able to test the circuits after the cut. Can someone tell me how I can test a specific member in a trunk group?

Any help is appreciated.

perform a status trunk or program "verify" button. By pressing the programed button, followed by the TAC 801 then press from 001 to 207.

December 11th, 2003, 10:15 AM	#1 (permalink)
redG PBXtech SILVER 25+ posts Join Date: Aug 2003 Posts: 98	How do I test members in a trunk group We have a G3r switch. We have a TAC of 801, the type is tie, and it has 207 members. We are going to cut over our 11 T1's to a fiber backbone and I need to be able to test the circuits after the cut. Can someone tell me how I can test a specific member in a trunk group? Any help is appreciated.

December 23rd, 2003, 07:18 PM	#4 (permalink)
bharris Join Date: Jul 2003 Posts: 18	Re: How do I test members in a trunk group Use the following command. status trunk 1/1 This gives the status for trunk number 1 member number 1. Use the trunk number(s) you have.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Trunk Audit	Stan Lee	Definity Servers	7	April 7th, 2006 07:32 PM
Changing Audix Hunt group members	liquidvw	Definity Servers	2	September 15th, 2005 12:04 PM
PRI setup assistance	nfarooqui	Definity Servers	6	August 23rd, 2005 05:25 PM
Trunk group question	tek	Definity Servers	1	February 10th, 2004 02:43 PM
extension to use only cetrain trunk members	mindyw	Definity Servers	1	January 2nd, 2004 09:56 AM

Remove advertisements
PBXtech.info Advertisement	Sponsored links

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)