dherve

Hello,
I want to replace TN2312AP by TN2312BP on a site, configuration is :

list configuration control Page 1

SYSTEM CONFIGURATION

Board Assigned Ports
Number Board Type Code Vintage u=unassigned t=tti p=psa

01A MAINTENANCE TN775D 000003 u u
01A IP SERVER INTFC TN2312AP HW02 FW021 01 02 03 04 05 06 07 08
01B IP SERVER INTFC TN2312AP HW02 FW021 01 02 03 04 05 06 07 08
02A MAINTENANCE TN775D 000003 u u
02A IP SERVER INTFC TN2312AP HW02 FW021 01 02 03 04 05 06 07 08
02B IP SERVER INTFC TN2312AP HW02 FW021 01 02 03 04 05 06 07 08
02D TONE/CLOCK TN2182B 000003 01 02 03 04 05 06 07 08
02E TONE/CLOCK TN2182B 000003 01 02 03 04 05 06 07 08
03A MAINTENANCE TN775D 000003 u u
03A TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
03B TONE/CLOCK TN2182B 000004 01 02 03 04 05 06 07 08
04A MAINTENANCE TN775D 000003 u u
04A TONE/CLOCK TN2182B 000004 01 02 03 04 05 06 07 08
04B TONE/CLOCK TN2182B 000004 01 02 03 04 05 06 07 08
05A MAINTENANCE TN775D 000003 u u
05A TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
05B TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
05D TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
05E TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
06A MAINTENANCE TN775D 000003 u u
06A TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
06B TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
06D TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
06E TONE/CLOCK TN2182C 000002 01 02 03 04 05 06 07 08
07A IP SERVER INTFC TN2312BP HW10 FW021 01 02 03 04 05 06 07 08
07B IP SERVER INTFC TN2312BP HW10 FW021 01 02 03 04 05 06 07 08
08A IP SERVER INTFC TN2312BP HW12 FW021 01 02 03 04 05 06 07 08
08B IP SERVER INTFC TN2312AP HW02 FW021 01 02 03 04 05 06 07 08

Do I only need to replace the board and that's all ?

Software configuration is : System: G3xV12 Software Version: R012x.02.0.111.4

Many thanks in advance.

martinyoung

Since your TN2312AP's are in port network 1 and 2, one of them will probably be your "golden IPSI" (usually 1A). That is a part of your license and the license will need to be updated to reflect the change. The old IPSI serial number must be replaced by the new IPSI serial number.

You cannot do that yourself, either Avaya or a Business Partner can help with that.

The firmware on the new IPSI's might also be old and need to be updated.

__________________
Marty
Retired Avaya DSIC tech

PBXtech.info

 

dherve

I am aware about that and my question was only about the process to change them.
It seems that I only need to replace the board and that's all no need to remove any other board, true ?

dherve

I am aware about the fact that I have to generate a new license.
My question was onyl regarding the process to change them. It seems that I only need to remove the TN2312AP and replace them and that's all, no need to remove other board etc ... true ?

martinyoung

Yes, all you need to do is replace the board. Nothing else needs replacing.

Since you have IPSI pairs (one in the A carrier and one in the B carrier) this implies critical reliability. I was going to say that the two IPSI's should be matched but I noticed that in port network 8 they are not. So, never mind :)

__________________
Marty
Retired Avaya DSIC tech