amart7

Hello, I am trying to use BSR with AVAYA SBS signalling. I have an R11.03 residing in Bournemouth-UK connecting to R12.02 stateside. Bournemouth is my point of entry for customer calls. I followed the SBS job aid that Avaya provided but when I place a test call I receive the following message in the Bournemouth VDN list trace when it hits the consider step for the far end in the US "NO DATA RETURNED FROM POLL "
Has anyone here implemented this solution and would you be willing to share configs.
Any ideas would be appreciated....Thanks,

stubborne

What does the status vector look like in the US?
In your BSR table you have a status and interflow VDN assigned for the US site. Each VDN is pointed to a vector. Your status vector should look something like:
consider skill X ...
reply-best

(no stop or busy)

__________________
Stu

PBXtech.info

 

amart7

Here is a copy of the vector
display vector 801 Page 1 of 3
CALL VECTOR
Number: 801 Name: *TEST BSR UK SP
Multimedia? n Meet-me Conf? n Lock? n
Basic? y EAS? y G3V4 Enhanced? y ANI/II-Digits? y ASAI Routing? y
Prompting? y LAI? y G3V4 Adv Route? y CINFO? y BSR? y Holidays? y
Variables? y
01 consider skill 300 pri m adjust-by 0
02 reply-best
03
04
05
06
07
08
09
10
11

liquidvw

what kind of circuit are you using for this poll. I have always used point to point circuits for polling. IP or T1 doesn't matter, but ISDN via the PSTN doesn't work.

amart7

Using IP trunk setup for SBS
Status Poll call routes over this trunk group.

SIGNALING GROUP
Group Number: 80 Group Type: h.323
Remote Office? n Max number of NCA TSC: 5
SBS? y Max number of CA TSC: 0
Trunk Group for NCA TSC: 80
Trunk Group for Channel Selection: 80
Supplementary Service Protocol: b

Near-end Node Name: C-Lan Far-end Node Name: 3Clan
Near-end Listen Port: 1720 Far-end Listen Port: 1720
Far-end Network Region: 3
LRQ Required? n Calls Share IP Signaling Connection? y
RRQ Required? n
Bypass If IP Threshold Exceeded? n
DTMF over IP: out-of-band Direct IP-IP Audio Connections? y
IP Audio Hairpinning? y
Interworking Message: PROGress
TRUNK GROUP
Group Number: 80 Group Type: isdn CDR Reports: y
Group Name: *TEST* BSR to Deleware(SBS) COR: 0 TN: 1 TAC:
Direction: two-way Outgoing Display? y Carrier Medium: IP
Dial Access? n Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: b Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: cyclical QSIG Value-Added? n
Digital Loss Group: 18
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0

ACA Assignment? n Measured: internal Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member: 5
Send Name: y Send Calling Number: y
Used for DCS? n Hop Dgt? n
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: shared
Maximum Size of UUI IE Contents: 128
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Send UUI IE? y
Send UCID? n BSR Reply-best DISC Cause Value: 31
Send Codeset 6/7 LAI IE? y
Path Replacement with Retention? n
Path Replacement Method: better-route
SBS? y Network (Japan) Needs Connect Before Disconnect? n

TRUNK GROUP
Administered Members (min/max): 1/5
GROUP MEMBER ASSIGNMENTS Total Administered Members: 5
Port Code Sfx Name Night Sig Grp
1: T00452 80
2: T00453 80
3: T00454 80
4: T00455 80
5: T00456 80
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:

amart7

I resolved this problem. The QSIG extension was not configured on the far-side of the T-1. Once I configured the extension it worked like a charm and requires no medpro resources.

PBXtech.info