Outgoing ANI - not working

nstarcorp · July 7th, 2003, 08:16 AM

We recently set up a new PRI DID/DOD Trunkgroup for an EPN. Can make incoming and outgoing calls but cannot get ANI to go out. We can get the lead number of a group of 100 to go but nothing else. Verizon says this is because we are not passing the ANI. Any suggestions?

tele234 · July 7th, 2003, 11:12 AM

did you set up the tie line as PRI ? set this up as pri and it will send ani across the D channel.. You will need to set up a new signal group for this...

nexSIP · July 7th, 2003, 11:14 AM

Well if you have a PRI you can send ANI.

change isdn public-unknown-numbering

Ext Len - 4
Ext Code - 1
CPN Prefix - 801555
Total CPN Len - 10

That is an example. for a 4 digit dial plan. extension 1xxx would have a ANI prefix of 801555

So extension 1505 would show ANI of 8015551505

mtfs · July 7th, 2003, 07:56 PM

If the lead number is passing i would think that verizon is the one sending the main number. You also have to set up each extension in the isdn public table.

July 7th, 2003, 08:16 AM	#1 (permalink)
nstarcorp Join Date: Jul 2003 Posts: 1	Outgoing ANI - not working We recently set up a new PRI DID/DOD Trunkgroup for an EPN. Can make incoming and outgoing calls but cannot get ANI to go out. We can get the lead number of a group of 100 to go but nothing else. Verizon says this is because we are not passing the ANI. Any suggestions?

July 7th, 2003, 11:14 AM	#3 (permalink)
nexSIP Moderator Join Date: Jun 2003 Posts: 527 Blog Entries: 3	Well if you have a PRI you can send ANI. change isdn public-unknown-numbering Ext Len - 4 Ext Code - 1 CPN Prefix - 801555 Total CPN Len - 10 That is an example. for a 4 digit dial plan. extension 1xxx would have a ANI prefix of 801555 So extension 1505 would show ANI of 8015551505 __________________ http://www.nexsip.com Communicate Openly and Freely

July 7th, 2003, 07:56 PM	#4 (permalink)
mtfs PBXtech GOLD 100+ posts Join Date: Jun 2003 Posts: 132	If the lead number is passing i would think that verizon is the one sending the main number. You also have to set up each extension in the isdn public table. Last edited by mtfs; July 7th, 2003 at 08:06 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANI Information	deepakjain	Definity Servers	1	August 8th, 2005 10:52 AM
How to get CDR to give the ANI	tek	Meridian systems	2	April 1st, 2005 07:52 AM
Does Anyone now if you can send the ANI for a VDN	BigMike	Definity Servers	1	August 24th, 2004 09:22 PM
ANI, identifying numbers	Greg-SD	Definity Servers	1	July 23rd, 2004 02:30 AM
This document will explain how to program a vector to play back the extension you are	nexSIP	Definity Servers	18	July 30th, 2003 03:22 PM

July 7th, 2003, 11:12 AM	#2 (permalink)
tele234 PBXtech SILVER 25+ posts Join Date: Jul 2003 Posts: 94	did you set up the tie line as PRI ? set this up as pri and it will send ani across the D channel.. You will need to set up a new signal group for this...

Remove advertisements Sponsored links
PBXtech.info Advertisement

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)