SLIPs

payton · June 26th, 2003, 02:14 PM

I have a T1 that aparently is SLIPping. (according to XO)
They said I need to set the clocking on my switch.

Anyone know how?

nexSIP · June 26th, 2003, 03:29 PM

change synchronization

Then just but your ds1 board location in the Primary.

mtfs · July 2nd, 2003, 05:30 PM

Heres a copy of mine

change synchronization Page 1 of 2
SYNCHRONIZATION PLAN

SYNCHRONIZATION SOURCE (circuit pack location)

Stratum: 4

Primary: 01A05 Secondary:

CIRCUIT PACKS AVAILABLE FOR SYNCHRONIZATION
Location Type Name Slip Location Type Name Slip
01A05 DS1 PaeTec PRI 2 y
01B04 DS1 PaeTec PRI y
01B10 DS1 AT&T y

NOTE: DS1 and BRI TRUNK sources result in stratum 4, type II synchronization

nexSIP · July 2nd, 2003, 10:10 PM

It would be better on your system to use 01B04 as Primary and 01b10 as Secondard.

If 01A05 were to die and you didnt have a secondary clocking source. you would be in trouble.

chrissa · July 3rd, 2003, 07:38 AM

Both the primary and secondary sync sources need to be in the same cabinet and carrier, if you use a secondary as well. And it's recommended that you have it in cabinet 1.

Also, if you do a list measurements ds1 summary UUCSS (where UUCSS is the ds1 board), you'll be able to see what kinds of errors there are on the T1 as well.

nexSIP · July 3rd, 2003, 11:23 AM

The newer software revs dont have that restriction
My clocking is on 01A18 and 02B19 running R11

June 26th, 2003, 02:14 PM	#1 (permalink)
payton PBXtech GOLD 100+ posts Join Date: Apr 2003 Posts: 121	SLIPs I have a T1 that aparently is SLIPping. (according to XO) They said I need to set the clocking on my switch. Anyone know how?

June 26th, 2003, 03:29 PM	#2 (permalink)
nexSIP Moderator Join Date: Jun 2003 Posts: 527 Blog Entries: 3	change synchronization Then just but your ds1 board location in the Primary. __________________ http://www.nexsip.com Communicate Openly and Freely

July 2nd, 2003, 10:10 PM	#4 (permalink)
nexSIP Moderator Join Date: Jun 2003 Posts: 527 Blog Entries: 3	It would be better on your system to use 01B04 as Primary and 01b10 as Secondard. If 01A05 were to die and you didnt have a secondary clocking source. you would be in trouble. __________________ http://www.nexsip.com Communicate Openly and Freely

July 3rd, 2003, 11:23 AM	#6 (permalink)
nexSIP Moderator Join Date: Jun 2003 Posts: 527 Blog Entries: 3	The newer software revs dont have that restriction My clocking is on 01A18 and 02B19 running R11 __________________ http://www.nexsip.com Communicate Openly and Freely

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Remove advertisements Sponsored links
PBXtech.info Advertisement

July 2nd, 2003, 05:30 PM	#3 (permalink)
mtfs PBXtech GOLD 100+ posts Join Date: Jun 2003 Posts: 132	Heres a copy of mine change synchronization Page 1 of 2 SYNCHRONIZATION PLAN SYNCHRONIZATION SOURCE (circuit pack location) Stratum: 4 Primary: 01A05 Secondary: CIRCUIT PACKS AVAILABLE FOR SYNCHRONIZATION Location Type Name Slip Location Type Name Slip 01A05 DS1 PaeTec PRI 2 y 01B04 DS1 PaeTec PRI y 01B10 DS1 AT&T y NOTE: DS1 and BRI TRUNK sources result in stratum 4, type II synchronization

July 3rd, 2003, 07:38 AM	#5 (permalink)
chrissa Join Date: Jul 2003 Posts: 22	Both the primary and secondary sync sources need to be in the same cabinet and carrier, if you use a secondary as well. And it's recommended that you have it in cabinet 1. Also, if you do a list measurements ds1 summary UUCSS (where UUCSS is the ds1 board), you'll be able to see what kinds of errors there are on the T1 as well.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Audix LX time slips	nexSIP	Definity Servers	1	April 26th, 2004 09:52 AM
Is there a way to look at timing slips and errors on the G3?	mtfs	Definity Servers	1	July 7th, 2003 10:19 PM