CAS protocol With Dialogic

dmouge · June 10th, 2003, 05:20 AM

Hello all,

We would like to setup a CAS (2Mb) between our Definity and our ENVOX server (IVR).

The IVR used Dialogic Board for the E1 connection but unfortunately the link doesn't works.

someone already setup up this kind of link and could provide the information about how to setup the defintiy and the Dialogic board ( the dialogic board are D300JCT and D600JCT).

Thanks in advance

David

payton · June 10th, 2003, 10:00 AM

This is how I have a T1 (PRI) setup which is connected to a dialogic board:

Location: 02A19.......................................Name: IS FAX
Bit Rate: 1.544.........................................Line Coding: b8zs
Line Compensation: 1..............................Framing Mode: esf
Signaling Mode: isdn-pri
Connect: pbx............................................Int erface: network
CentreVu Long Timers? n.........................Country Protocol: 1
Interworking Message: PROGress............Protocol Version: a
Interface Companding: mulaw..................CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz

Slip Detection? n Near-end CSU Type: integrated

mtfs · June 15th, 2003, 06:55 PM

Did this work for you???

dmouge · June 16th, 2003, 02:22 AM

Hi,

We have setup at the moment the system like this with isdn 2.0MB.

Now my problem is that with this configuration i don't have the possibility to used the converse-on skill .... in my vector.

payton · June 16th, 2003, 10:39 AM

Paste your vector here and lets see what we can do!

dmouge · June 17th, 2003, 03:21 AM

This is not the vector who is in fault. We have some conversant behind our system and we already setup the vector step .....

My problem is the link with the Dialogic board. currently it's ISDN but i would like to change it to CAS (in order to used station / login ) and converse-on step.on the definity side it's ok but on thedialogic side not.
Do you know a forum or something like this where i can found some Dialogic expert ?

Admin · June 17th, 2003, 03:36 AM

so the problem is you dont know how to configure CAS on the dialogic board..?

dmouge · June 17th, 2003, 03:44 AM

Yes it seems that each PBX and each conutry have different TONE and we need it in order to send a file to the dialogic baord in order to setup this but I don't have this files. sorry if my question was not really clear at the start...
We receive the response from AVAYA how to setup the board from the definity Side in order to used station / agent.

June 10th, 2003, 05:20 AM	#1 (permalink)
dmouge Join Date: Jun 2003 Posts: 5	CAS protocol With Dialogic Hello all, We would like to setup a CAS (2Mb) between our Definity and our ENVOX server (IVR). The IVR used Dialogic Board for the E1 connection but unfortunately the link doesn't works. someone already setup up this kind of link and could provide the information about how to setup the defintiy and the Dialogic board ( the dialogic board are D300JCT and D600JCT). Thanks in advance David

June 10th, 2003, 10:00 AM	#2 (permalink)
payton PBXtech GOLD 100+ posts Join Date: Apr 2003 Posts: 121	This is how I have a T1 (PRI) setup which is connected to a dialogic board: Location: 02A19.......................................Name: IS FAX Bit Rate: 1.544.........................................Line Coding: b8zs Line Compensation: 1..............................Framing Mode: esf Signaling Mode: isdn-pri Connect: pbx............................................Int erface: network CentreVu Long Timers? n.........................Country Protocol: 1 Interworking Message: PROGress............Protocol Version: a Interface Companding: mulaw..................CRC? n Idle Code: 11111111 DCP/Analog Bearer Capability: 3.1kHz Slip Detection? n Near-end CSU Type: integrated Last edited by payton; June 10th, 2003 at 10:02 AM.

June 17th, 2003, 03:36 AM	#7 (permalink)
Admin Administrator Join Date: Jun 2003 Posts: 133 Blog Entries: 2	so the problem is you dont know how to configure CAS on the dialogic board..? __________________ Review your Telephone system here http://www.pbxsales.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dialogic Card	desrae	Definity Servers	8	September 10th, 2008 12:21 PM
Meridian PBX - Dialogic Card	Gulano	Meridian systems	0	March 2nd, 2006 05:41 AM
Problem with CAS Protocol	murali	Definity Servers	1	October 28th, 2004 08:18 PM
Buying Buying used and broken Dialogic boards	DialogicBoards	Vendors (Discussion and Advertisments)	1	July 9th, 2003 02:49 PM
Dialogic Boards for sale	DialogicBoards	Vendors (Discussion and Advertisments)	1	July 9th, 2003 02:46 PM

Remove advertisements Sponsored links
PBXtech.info Advertisement

June 15th, 2003, 06:55 PM	#3 (permalink)
mtfs PBXtech GOLD 100+ posts Join Date: Jun 2003 Posts: 132	Did this work for you???

June 16th, 2003, 02:22 AM	#4 (permalink)
dmouge Join Date: Jun 2003 Posts: 5	Hi, We have setup at the moment the system like this with isdn 2.0MB. Now my problem is that with this configuration i don't have the possibility to used the converse-on skill .... in my vector.

June 16th, 2003, 10:39 AM	#5 (permalink)
payton PBXtech GOLD 100+ posts Join Date: Apr 2003 Posts: 121	Paste your vector here and lets see what we can do!

June 17th, 2003, 03:21 AM	#6 (permalink)
dmouge Join Date: Jun 2003 Posts: 5	This is not the vector who is in fault. We have some conversant behind our system and we already setup the vector step ..... My problem is the link with the Dialogic board. currently it's ISDN but i would like to change it to CAS (in order to used station / login ) and converse-on step.on the definity side it's ok but on thedialogic side not. Do you know a forum or something like this where i can found some Dialogic expert ?

June 17th, 2003, 03:44 AM	#8 (permalink)
dmouge Join Date: Jun 2003 Posts: 5	Yes it seems that each PBX and each conutry have different TONE and we need it in order to send a file to the dialogic baord in order to setup this but I don't have this files. sorry if my question was not really clear at the start... We receive the response from AVAYA how to setup the board from the definity Side in order to used station / agent.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)